Tripp-lite SS7415-15 User Manual download pdf

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234

www.tripplite.com

Tripp Lite Power Strips

Standard Models

Your Power Strip is designed to provide convenient multiple AC outlets.

SS Power Strips models (e.g. the SS7415-15) provide 450 joules of surge suppression to connected equipment.

Select models with surge suppression feature a green LED that lights when surge suppression components are

operating. All other Power Strips DO NOT provide connected equipment with surge or line noise protection.

ELECTRICAL CONNECTION

Plug your Power Strip into a standard, grounded electrical outlet. DO NOT plug your Power Strip into 2-wire

extension cords or adapters. DO NOT drill into or open any part of the housing. There are no user-serviceable

parts inside.

EQUIPMENT CONNECTION

Plug your equipment into the Power Strip’s AC receptacles. DO NOT plug in equipment that draws more total

amps than your Power Strip's amperage rating (see label on Power Strip for amperage rating), or you will trip

the circuit breaker. If the circuit breaker trips, remove overload and depress breaker to reset. Leave enough clearance

at the end of the Power Strip to allow the circuit breaker to operate normally.

Note: Select models with a power switch feature a protective switch cover. To access the switch, simply flip open the attached cover.

WALL MOUNTING

All standard Power Strip models feature clips for horizontal or vertical mounting on a variety of surfaces. The

user must supply other mounting hardware (screws, etc.) and determine their suitability for use with the chosen

mounting surface.

Mark a straight horizontal or vertical line where you want to

mount the Power Strip. At each end of the line, mark where

the edges of the Power Strip will be located. Place a mounting

clip on the mounting surface 1” in from these edges and mark

where the screws must be driven into the wall. For strips

longer than 48" (120 cm), also mark a screw hole for a third

mounting clip midway between the other two.

KKeeyyhhoollee MMoouunnttiinngg::

Drive #8 screws directly into the mount-

ing surface. Snap the mounting clips onto the Power Strip

(2a), then hang the Power Strip on the screws by the keyhole

slots on its mounting clips (2b).

CClliipp MMoouunnttiinngg::

Drive #10 screws through washers, through

the centers of the mounting clips and into the mounting

surface (3a). Place the Power Strip inside one edge of the

mounting clips, then snap the Power Strip into place (3b).

Français : p. 2; Español: p. 3

1 2 3 4 5

Summary of Contents

Page 1 - Tripp Lite Power Strips

1111 W. 35th Street Chicago, IL 60609 USACustomer Support: (773) 869-1234www.tripplite.comTripp Lite Power StripsStandard ModelsYour Power Strip is d

Page 2 - Modèles standard

1111 W. 35th Street, Chicago, IL 60609 EUAService à la clientèle : 1 + (773) 869-1234www.tripplite.comPlaquettes d'alimentation Tripp LiteModèles

Page 3 - Modelos estándar

1111 W. 35th Street Chicago, IL 60609 EE UUAtención al cliente: +1 (773) 869-1234www.tripplite.comBarras de Contactos de Tripp LiteModelos estándarCU

Page 4

4200110023 93-2005LIFETIME LIMITED WARRANTYSeller warrants this product, if used in accordance with all applicable instructions, to be free from orig

Page 5 - 200110023 93-2005_ES

1111 W. 35th Street, Chicago, IL 60609 USA 773.869.1234 (USA) • 773.869.1212 (International) www.tripplite.com200110023 93-2005_ES

Comments to this Manuals

No comments

Tripp-lite SS7415-15 User Manual

Browse online or download User Manual for Computer Accessories Tripp-lite SS7415-15. Tripp Lite SS7415-15 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Computer Accessories Tripp-lite SS7415-15