Tripp Lite RELAYIOCARD Owner's Manual download pdf (Page 7)

PROGRAMMABLE RELAY I/O CARD

USER MANUAL

PRESENTATION

FEATURES

This relay I/O card is an UPS management

product with 6 relay output contacts for monitoring

the status and 1 input contact as a shutdown UPS

or a battery test command.

Features:

z Monitor UPS events.

z 6 programmable relay output contacts.

z Configurable normal open or normal close for

each relay contact.

z Configurable UPS shutdown delay time.

z Configurable input signal as shutdown UPS or

battery test.

z Has the ability to protect up to 6 computers

unattended shutdown gracefully.

TECHNICAL SPECIFICATION

Size 130 x 60 mm

Weight 200 g

Operating Temperature 0 ~ 40° C

Operating Humidity 10 ~ 80 %

Power Input 8 ~ 20V DC

Power Consumption 1.2 Watts

OUTPUT CONTACT RATING

Maximum

DC Voltage DC Current

Relay

R1~R6

24 V 1A

INPUT RATING

Maximum

DC Voltage DC Current

Input 24 V 10 mA

APPLICATION EXAMPLE

In this case we’ll use the default settings, please

set SW1 and SW2 to the OFF position. Apply

12VDC to Common contact and connect the

lamps to R1~R6 terminals. Install a push button

from the Common contact to the input terminal.

Press the button for at least 3 seconds to

shutdown the UPS remotely.

Common

G N D- R

Input

+12V

Summary Alarm

Power Fail

Battery Low

On Bypass

Overload

Shutdown UPS

Over Temperature

INTERNAL CIRCUIT

Common

GND-R

Input

+5V

CPU Pin

OUTLINE

GND-R

Common

Input

GND-C

SW1

SW2

I/O PINOUT

GND-R: Ground for relays

Common: 12~24VDC

Default Alarm Event

R1 Summary Alarm

R2 Power Fail

R3 Battery Low

R4 On Bypass

R5 Overload

R6 Over Temperature

Input: Remote shutdown or battery test

Tx: Transmit to PC, connect to sub9-pin2

Rx: Receive from PC, connect to sub9-pin3

GND-C: Ground for configuration Tx and Rx pins

OFF (Default) ON

SW1 Normal open

for default settings

Normal close

for default settings

SW2 Default settings Customized settings

PROGRAMMABLE CONTACTS

COMMUNICATION SETUP

1. Connect Tx to pin2, Rx to pin3 and GND-C to

pin5 of PC RS232 port.

2. In the Windows environment, launch the

Hyper- Terminal program then open the

specified COM port.

3. Set the following properties:

Baud rate: 2400, Data Bits: 8, Parity: None

Stop Bit: 1, Flow Control: None

CONFIGURATION

1. Press <Enter> to get the main menu of the

programmable relay card.

+---------------------------+

| UPS Relay Card |

+---------------------------+

Firmware Version: Relay Card V1.4

[1].Customize Output Relay

[2].Configure Input Signal

[3] Customize Normal Open or Normal Close

[0].Quit

Please Enter Your Choice =>

2. Press ‘1’ to configure the alarm event for

R1~R6.

Contacts R1~R6 can be configured for

different power events.

+---------------------------+

| Customize Output Relay |

+---------------------------+

Relay Selected Event

[1].Relay1: Summary Alarm

[2].Relay2: Power Fail

[3].Relay3: Battery Low

[4].Relay4: On Bypass

[5].Relay5: Overload

[6] Relay6: Over Temperature

[0].Back To Previous Menu

Please Enter Your Choice =>

Once the configuration is complete SW2

MUST be switched to the ON position to apply

the new settings, switch SW2 back to the OFF

position to reset to the default settings.

3. Press ‘2’ to configure the Input signal.

+---------------------------+

| Configure Input Signal |

+---------------------------+

[1].Act as Shutdown or Test: Shutdown

[2].Input Signal Confirm: 3 Seconds

[3].Delay Before Shutdown: 30 Seconds

[0].Back To Previous Menu

Please Enter Your Choice =>

In this menu, the input signal can be redefined

as shutdown UPS or battery test signal.

Meanwhile, the UPS shutdown delay time is

also adjustable to a maximum of 9999

seconds.

4. Press ‘3’ to configure the normal open or

normal close for each relay.

+---------------------------+

| Customize Output Relay |

+---------------------------+

Relay Selected Event

[1].Relay1: Normal Close

[2].Relay2: Normal Open

[3].Relay3: Normal Close

[4].Relay4: Normal Open

[5].Relay5: Normal Close

[6].Relay6: Normal Open

[0].Back To Previous Menu

Please Enter Your Choice =>

Once the configuration is complete SW2

MUST be switched to the ON position to apply

the new settings. Switch SW2 back to the

OFF position to reset to the default settings.

5. Press ‘0’ to quit this configuration session.

The system would prompt you to save or not.

Press ‘Y’ to save your settings, ‘N’ to ignore.

POWER OPTION IN WIN 2000/XP

This relay card has the ability to provide UPS

signals for Windows NT4/2000/XP/2003. First

connect the RS232 port on the PC to the relay

card as shown:

Then open the power option from control panel

and click on the UPS tab to setup the signals

polarity, select Positive for Power Fail, Low

Battery and UPS

Shutdown.

Since the R1~R6

contacts are

programmable,

the output

contacts can be

configured for 3

computers with 2

signals (power fail

and low battery) or

6 computers with

one signal (power

fail or low battery).

Note: All of the computers must have the same

earth ground potential. Connect all of the

computers input power to the same UPS.

Common

GND-R

Input

Power Fail

Battery Low

RTS pin7

GND pin5

CTS pin8

DCD pin1

DTR pin4

Shutdown UPS

1. Introducción

2. Instalación y Configuración

1.1 Características del Producto

RELAYIOCARD es un dispositivo de administración de UPS programable que cuenta con:

• 6 contactos de salida de relé programable

• Abertura normal o cierre normal configurables para cada cierre de relé

• Tiempo de retardo de apagado configurable del UPS

• Señal de entrada configurable para apagar el UPS o probar la batería

La RELAYIOCARD le permite:

• Monitorear el estado y los eventos del UPS

• Realizar apagados del sistema y pruebas de la batería de manera remota

1.2 Contenidos del Embalaje

Este Embalaje Contiene:

• RELAYIOCARD

• Cable de configuración

• Placas frontales

• Manual del propietario

2.1 Requisitos del Sistema

La RELAYIOCARD admite todos los sistemas UPS SmartOnline™ y sistemas UPS SmartPro™ selectos de Tripp Lite,

que incluyen SMART1050SLT, SMART1500SLT, SMART2200RMXL2U, SMX1050SLT, SMX1500SLT, SMART3000SLT,

SMART2200SLT, SM2200RMNAFTA, SMART2600RM2U, SMART3000RM2U, SMART1500CRMXL, SMART1500SLTXL,

SMART750XLa, SMX3000XLRT2U y SMX2200XLRT2U. Los sistemas admitidos ejecutarán un protocolo de UPS de

3008 o superior.

Para determinar su protocolo UPS:

1. Abra el software PowerAlert de Tripp Lite.

2. Haga clic en el botón “Misc” (Misceláneo) en la pantalla principal de la consola de PowerAlert.

3. Vea la variable del protocolo.

2.2 Configuración de Comunicaciones

1. Conecte Tx a pin 2, Rx a pin 3 y GND-C a pin 5 del puerto de RS-232 DB9.

2. En el entorno de Windows, abra el programa Hyper Terminal, luego abra el puerto COM especificado.

3. Ajuste las siguiente propiedades– velocidad en baudios: 2400, Bits de datos: 8, Paridad: Ninguna, Bit de parada: 1,

Control de flujo: Ninguno.

201011142 932815.indb 7 1/6/2011 9:15:48 AM

1 2 3 4 5 6 7 8 9 10 11 12 ... 15 16

Comments to this Manuals

No comments

Tripp Lite RELAYIOCARD Owner's Manual Page 7

Comments to this Manuals