SNMP Solo™Owner’s Manualfor:SNMP Solo™by:MT-SE-37/02 Copyright © 199912-DEC-99 93-1469 (9909097) 12/99
SNMP Solo4SNMP Solo Package Network connection ports—SNMP Solo provides a BNCconnector for 10Base-2 connection and a UTP (RJ-45)connector for 10Base-T
Tripp LiteSNMP Solo Package 5 Serial Port The SNMP Solo uses this port for configuration duringinstallation or for communications during normal operat
SNMP Solo6SNMP Solo Package UPS Interface Cable The manufacture-specific interface cable connects the UPS tothe SNMP Solo unit. The table below define
Tripp LiteSystem Requirements 7 System Requirements SNMP Solo requires a terminal for configuration and a networkconnection with an NMS for operati
SNMP Solo8System Requirements
Tripp LiteInitial Installation 9Initial InstallationThis section describes the installation of the SNMP Soloadapter when you connect it to the UPS and
SNMP Solo10Initial Installationb) A Windows’s communication screen with the typicalSNMP Solo setting:Figure 4 Communication Screen (Windows) 5. Pres
Tripp LiteConfiguration 11ConfigurationYou have previously installed the UPS, and you are ready toconfigure the SNMP Solo to work on your network. SNM
SNMP Solo12ConfigurationSet IP And Gateway AddressesAnd MIB System GroupTo set the IP address, Gateway address, MIB system group,and other system conf
Tripp LiteConfiguration 13To assign the IP address of SNMP Solo, the gateway, and thenetwork, type at the prompt:1, <space>, the IP address of t
Limited WarrantyTripp Lite warrants that each product sold by Tripp Lite is compatible with existingcommercially available computer operating environm
SNMP Solo14ConfigurationClass B Network0 255.255.000.000 8 255.255.255.0001 255.255.128.000 9 255.255.255.1282 255.255.192.000 10 255.255.255.1923 255
Tripp LiteConfiguration 15The top of the screen displays your new values:Record the definitions on your Worksheet for reference. Toreturn to the Main
SNMP Solo16ConfigurationTo set an access control, at the prompt type:Set, <space>, enter the number of the column from 1 through 4,<space>
Tripp LiteConfiguration 17Figure 8 Trap ReceiversTo set traps, at the prompt type:Set, <space>, enter the number of the column from 1 through 4
SNMP Solo18Configuration To remove a trap receiver from the list, type clear, <space>,and the desired list number at the prompt. Press <enter
Tripp LiteConfiguration 19After you have set the UPS address, you can return to the mainsetup screen by typing 0 and pressing Enter.NOTE: The UPS addr
SNMP Solo20Configuration• Location (location of your UPS and SNMP Solo)• List of the current communities with their access controlcode• List of the
Tripp LiteConfiguration 21This messages informs or directs you:1. The Setup program has ended.2. Turn off the DIP switch (switch 1 UP).3. Disconnec
SNMP Solo22ConfigurationUpload FirmwareCAUTION: The firmware upload has already been accomplished at thefactory. Before you proceed with this option,
Tripp LiteFinal Installation 23Final InstallationNow that you have completed Configuration you are ready toconnect the SNMP Solo to your UPS and to th
Governing LawThis statement shall be construed, interpreted, and governed by the laws of theState of Illinois.YOU ACKNOWLEDGE THAT YOU HAVE READ THIS
SNMP Solo24Final InstallationIf the SNMP Solo detects three communicationfailures in a row, the red LED turns on andstays on until the SNMP Solo recei
Tripp LiteConfiguring the NMS 25Configuring the NMSTo complete the SNMP Solo installation and configurationprocess, you must compile the necessary MIB
SNMP Solo26Configuring the NMS4. Enter a name for the object in the Selection and Labelfields of the Add Object box.5. Highlight IP Map from Object A
Tripp LiteConfiguring the NMS 27Add SNMP Solo Object to the Management MapThe NMS will discover the NetMon and add it to theManagement map during its
SNMP Solo28Configuring the NMSSunConnect SunNet ManagerCompile the Device MIB1. Copy the UPS MIB file from the TAR formatted diskette intothe subdire
Tripp LiteConfiguring the NMS 29Poll the Device OIDs1. Select the device glyph with the right mouse button.2. Select Quick Dum, *-MIB then one of th
SNMP Solo30AppendixAppendixThis appendix has three sections: Reference, Glossary, andTroubleshooting.ReferenceThis section discusses Communities, IP A
Tripp LiteAppendix 31number of octets reserved for the network ID and the number ofoctets reserved for the host ID.Class Value of FirstOctetNetwork ID
SNMP Solo32Appendixown subnetwork, set the subnet mask to 255.255.255.0 for thedevices on that subnetwork.Subnet MaskRouting and Filtering0.0.0.0IP pa
Tripp LiteAppendix 33GlossaryThe Glossary section defines the terms used in the SNMP Soloenvironment.AgentImplemented SNMP applications in network ele
TrademarksSNMP Solo is a trademark of Tripp Lite.IBM, IBM NetView/6000 are trademarks or registeredtrademarks of International Business Machines Corp.
SNMP Solo34AppendixNONormally Open—Refers to a contact switch that is normallyopen.OIDObject Identifier—The variables defined in a MIB.PersonalityThe
Tripp LiteAppendix 35TroubleshootingProblem: The TES (Terminal Emulation Software) does not displayanything.Solution: Make sure the Dip switch is set
SNMP Solo36AppendixPlacing a Technical Support CallIn order to diagnose the problem you are having, our technicians needthe following information from
Tripp LiteAppendix 37" Technical Support "If you have any questions about your SNMP Solo orabout any Tripp Lite product, you can contact u
SNMP Solo38Reference WorksheetReference WorksheetLocal Address: ___.___.___.___ Serial No: __:__:__:__:__:__Gateway Address: ___.___.___.___Netw
Tripp LiteTable of Contents iTable of ContentsIntroduction ... 1SNMP Solo Features ... 1Example Ne
SNMP SoloiiIntroductionCompile the Device MIB ... 25Add SNMP Solo Object to the Management Map.. 25Poll the Device OIDs ...
Tripp LiteIntroduction 1IntroductionYour SNMP Solo monitors one UPS attached to an EtherNetnetwork using a Network Management Station. The completeSNM
SNMP Solo2Introduction Example Network With SNMP Solo A typical installation of SNMP Solo monitoring a UPS on anEtherNet network follows in the illust
Tripp LiteSNMP Solo Package 3 SNMP Solo Package The standard SNMP Solo package contains a NetMon Unit withsupporting hardware and software. SNMP Sol
Comments to this Manuals