Tripp-lite OMNIVSINT800 User Manual download pdf (Page 8)

Specifications

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

Model: OMNIVSINT800 OMNIVSINT1000 OMNIVSINT1500XL

Series: AGOM4901 AGOM4901 AGOM4775

Input Voltage/Frequency: 230VAC/50/60 Hz 230VAC/50/60 Hz 230VAC/50/60 Hz

Output Capacity (VA/Watts): 800/475 1000/500 1500/940

Battery Runtime (Half Load/Full Load) Minutes: 19/6 18/7 14/5+

Battery Recharge Time: 2-4 hrs. 2-4 hrs. 2-4 hrs.

Approvals: CE, GOST, SASO, IRAM CE, GOST, SASO, IRAM CE, GOST, SASO, IRAM, TUVGS

Tel/Fax/Data Protection: 1-line tel/DSL 1-line tel/DSL 1-line tel/DSL/Ethernet

Output Voltage Line Mode (230VAC); Output Voltage On Battery (230VAC). Output Waveform Line Mode (filtered sinewave); Output Waveform Battery Mode (PWM sine wave); AC Surge

Suppression (exceeds IEEE 587 Cat. A & B standards); AC Noise Attenuation (>40 dB at 1MHz); AC Protection Modes (H to N).

Battery runtime for OMNIVSINT1500XL can be extended with the addition of a single optional Tripp Lite External Battery Pack which is not expandable (model # BP24V14, sold separately).

An External Battery will increase both the battery runtime and the battery recharge time.

Note on Labeling

Two symbols are used on the label.

V~ : AC Voltage

V : DC Voltage

Storage

All connected equipment should be turned off, then disconnected from the UPS to avoid battery

drain. Unplug the UPS from the wall outlet; then press and hold the ON/OFF/STANDBY button for

one second. The UPS will be completely “OFF” (deactivated). Your UPS is now ready for stor-

age. If you plan on storing your UPS for an extended period of time, fully recharge the UPS bat-

teries once every three months by plugging the UPS into a live AC outlet and letting the UPS

charge for up to 4 hours. If you leave your UPS batteries discharged for an extended period of

time, they will suffer a permanent loss of capacity.

Service

Before returning your UPS for service, follow these steps:

1. Review the installation and operation instructions in this manual to ensure that the service

problem does not originate from a misreading of the instructions. Also, check that the UPS

System’s circuit breaker(s) are not tripped. This is the most common cause of service

inquiries which can be easily remedied by following the resetting instructions in this manual.

2. If the problem continues, do not contact or return the UPS to the dealer. Instead, call Tripp Lite

at (773) 869-1233. A service technician will ask for the UPS's model number, serial number

and purchase date and will attempt to correct the problem over the phone.

3. If the problem requires service, the technician will issue you a Returned Material

Authorization (RMA) number, which is required for service. If you require packaging, the

technician can arrange to send you proper packaging. Securely pack the UPS to avoid damage

during shipping. Do not use Styrofoam beads for packaging. Any damages (direct, indirect,

special, incidental or consequential) to the UPS incurred during shipment to Tripp Lite or

an authorized Tripp Lite service center is not covered under warranty. UPS Systems shipped

to Tripp Lite or an authorized Tripp Lite service center must have transportation charges

prepaid. Mark the RMA number on the outside of the package. If the UPS System is within

the 2-year warranty period, enclose a copy of your sales receipt. Return the UPS for service

using an insured carrier to the address given to you by the Tripp Lite service technician.

Storage & Service

200404081 932242 OmniVSINT800_1000_ 1500XL Owners Manual .qxd 6/8/2004 11:36 AM Page 8

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 31 32

Comments to this Manuals

No comments

Tripp-lite OMNIVSINT800 User Manual Page 8

Comments to this Manuals

Related products and manuals for Tools Tripp-lite OMNIVSINT800